- INSTALLING GREDDY EMANAGE BLUE IN MA70 HOW TO
- INSTALLING GREDDY EMANAGE BLUE IN MA70 INSTALL
- INSTALLING GREDDY EMANAGE BLUE IN MA70 SERIAL
- INSTALLING GREDDY EMANAGE BLUE IN MA70 FULL
I’ve heard others having this problem, I think they just had the wires backwards. I had this happen when the rx and tx wires were backwards. The tool reports itself as online, but when I try to do anything it says “MAIN UNIT UPDATE” and “Corresponding… Please Wait” I hope you don’t have to read this, fortunately I ran accross many problems and maybe I have a fix for you. If it prompts for a file, select the one that shows up in the dialog box or look for one within the emanage program directory. The program may ask for a main unit update, in which case allow it to do so. Turn on the car (ACC) and then start emanage. Plug the cable into your computer before loading the program. Move these files over top of where you installed the management tool 1.11 (defaults to C:\Program Files\TRUST\GReddy e-manage support tool). Copy all files except eUp.ini and eUp.exe. When that happens, exit out of it, and navigate to the directory where the files were extracted to.
INSTALLING GREDDY EMANAGE BLUE IN MA70 INSTALL
I’ve never found this update to install correctly, often failing with non-english errors. This must be changed, change this to an area such as c:\temp. Following that run e-manage149.EXE, it will ask for an extraction directory and defaults to a temporary directory. Use winrar (provided on same group) to extract v1.11.rar then find and run the setup.exe. Sign up, and download e-manage149.EXE as well as v1.11.rar. Here is a picture of my end result:Įmanage can be downloaded from this emanage group on yahoo. USB Sideīe sure to use a multimeter to check that you really have vcc, or gnd, etc before soldering into the board. Here is where the USB connector wires should go to, use the chart and the image pinout of the usb to link it all together. They should be labelled or your part should have instructions. Look at your converter and find where the +5, Ground, tx and rx outputs are. Strip the end of every wire (very little needs to be showing, perhaps 2 or 3 mm. You can simply cut off the mesh/foil shielding for this. They are most commonly coloured as red/black/white/green though can be any colour combination. Using your hands pull this back and unravel it to reveal the four wires on the inside. Strip your usb cable, there will be a foil and/or braided meshjust below the plastic. You will need one of these that will accept an operating voltage of 5 volts.
INSTALLING GREDDY EMANAGE BLUE IN MA70 SERIAL
The standard serial port communicates with voltages levels -/+10v, however communication with the Emanage requires a range of 0-5v as it is a Logic Level device. There are hundreds of these listed, often below $10.00 USD (shipping included). These are rather common and can be found locally if you have a good electronics shop, otherwise eBay works great. The other piece of the puzzle is a 5-volt RS232 to TTL Converter. a mouse) and cut the end off, leave as much length as you can. If you can, find an older piece of computer equipment you dont need (i.e. You will need a USB-A cable, just one end.
![installing greddy emanage blue in ma70 installing greddy emanage blue in ma70](https://i.ytimg.com/vi/DEB3YBMSA_8/maxresdefault.jpg)
Spare USB cable to cut up (USB-A, the flat rectangular kind) Step 1 – Acquire Parts Willingness to buy parts from eBay (Rs232 TTL converter) The Greddy Emanage cable is NOT just a simple USB-USB, and it is also not the run of the mill usb-serial connector.
INSTALLING GREDDY EMANAGE BLUE IN MA70 HOW TO
Here, and I must say I’m a bit late with this older system, I will try my best to provide a detailed description on the wiring and a guide on how to achieve the creation of this cable which would otherwise cost over 150$ USD from Greddy dealers.
INSTALLING GREDDY EMANAGE BLUE IN MA70 FULL
I set out to see the full picture and work with the right parts instead of hoping that a specific usb phone cable would be the part I was looking for. I had tried other DIY’s but they were somewhat unclear and I never had results. Quite some time ago during some emission’s failures I sought a way to interact with my greddy emanage blue.